济南中阳石磨电器有限公司

全国热线电话:

17116125111

热门搜索: 豆浆石磨机 石磨面粉机 豆浆石磨机 石磨面粉机
联系我们
    济南中阳石磨电器有限公司
  • 联系:和经理
  • 电话:17116125111
  • 手机:17116125111
  • 邮箱:3471464452@qq.com
  • 网址:http://www.zysmcn.com
  • 厂址:山东省济南市章丘区相公庄镇
新闻资讯 您现在的位置:首页 - 新闻资讯

石磨芝麻酱机毛病的排除方法

来源:http://www.zysmcn.com/发布时间:2021-05-07

石磨芝麻酱机电机毛病:温度过高是电机损坏的主要原因之一。毛病原由于轴承缺油、轴承内进入脏物、轴承损坏、电机过载等。

1 、石磨芝麻酱机电机毛病:温度过高是电机损坏的主要原因之一。毛病原由于轴承缺油、轴承内进入脏物、轴承损坏、电机过载等。
1. Problems with the motor of Shimo sesame paste machine: high temperature is one of the main causes of motor damage. Due to lack of oil in bearing, dirt in bearing, bearing damage, motor overload, etc.
2、整理筛毛病:①整理筛振动大或筛框晃动,原由于螺栓或木楔松动。②砂石中带有麦料,新型石磨芝麻酱机,原因是排石嘴内部风门小,或筛面倾角不合适。③小麦被打碎过多,小型石磨芝麻酱机,原由于打麦装置齿板与筛片空隙太小,筛孔过大或损坏。
2. Problems of finishing screen: ① the vibrating of finishing screen or shaking of screen frame is caused by loose bolts or wedges. ② There is wheat material in the sand and stone. The new type of stone grinding sesame paste machine is due to the small air door inside the stone discharge nozzle or the improper inclination angle of the screen surface. ③ There are too many broken wheat in the small stone grinding sesame paste machine, because the gap between the tooth plate and the sieve plate of the threshing device is too small, the sieve hole is too large or damaged.
芝麻酱石磨机
3、石磨芝麻酱机螺旋搅拌器毛病:①出粮口不排粮,原由于电机转向不对,出料口阻塞,石磨芝麻酱机,搅拌器叶片开裂等。②搅拌器轴不转,原由于喂料过多,传动带打滑等。
3. Problems of screw mixer of Shimo sesame paste machine: ① the grain outlet does not discharge grain, because the motor turns wrong, the outlet is blocked, the blades of Shimo sesame paste machine and mixer are cracked, etc. ② The agitator shaft does not rotate because of too much feeding and the drive belt slipping.
4、石磨芝麻酱机毛病:①机身晃动,应拧紧磨头与机架联接螺栓。②产值下降,应调紧弹簧,保证磨辊两端空隙一致,对磨损的磨齿进行修理。③面粉温度高,应调松磨辊;如磨辊磨损严重应修理或替换;机温高时就停机散热。④不出麸皮,原由于主轴转向不对,筛框密封不严或筛网破损。⑤不出粉或出粉少,原由于筛阻塞。
4. Problems of stone mill sesame paste machine: ① the machine body shakes, so the connecting bolts between grinding head and frame should be tightened. ② When the output value decreases, the spring should be adjusted to ensure the gap at both ends of the roller is consistent, and the worn grinding teeth should be repaired. ③ If the flour temperature is high, the roller should be loosened; If the roller is seriously worn, it should be repaired or replaced; When the temperature of the machine is high, it will be shut down for heat dissipation. ④ No bran, because the main shaft steering is not right, the screen frame seal is not tight or the screen is damaged. ⑤ No powder or less powder, the reason is that the screen is blocked.
5、石磨芝麻酱机闭风器毛病:闭风不好,面袋可能被吸上。原由于各衔接处漏风,叶轮磨损等。叶轮磨损时可在外缘加装一块橡胶板。
5. Problems of air shutter of Shimo sesame paste machine: the air is not closed well, and the face bag may be sucked up. The reason is that there is air leakage at each joint and the impeller is worn. When the impeller is worn, a rubber plate can be added on the outer edge.
6,布滤筒毛病:①室内飞尘多,原由于分配箱集尘器不紧密、布筒未扎紧、接风管漏风等。②布滤筒内面粉过多,原由于风量大,集粉器下端衔接处漏风或磨穿,闭风叶轮与外壳空隙大。
6. Problems of cloth filter: ① there is a lot of dust in the room, which is caused by the loose dust collector of the distribution box, the cloth filter is not tied tightly, and the air leakage of the air duct. ② There is too much flour in the cloth filter barrel. Due to the large air volume, the connection at the lower end of the powder collector leaks or wears through, and the gap between the closed air impeller and the shell is large.
7、石磨芝麻酱机电器毛病:①机组不能发动,常见原由于电压过低,配电线缺线,线路接触不好,操控回路断线,保险丝熔断等。②电机不能发动,原由于电机操控回路接触不好或断线,沟通接触器线圈烧坏等。
7. Electrical problems of Shimo sesame paste machine: ① the unit can't be started, the common reasons are low voltage, lack of distribution line, poor line contact, broken control circuit, fuse, etc. ② The motor can not be started because the motor control circuit is not well contacted or broken, and the coil of communication contactor is burnt out.
相关新闻
相关产品
首页 走进中阳 产品中心 石磨小吃 新闻资讯 联系我们 网站地图 XML TXT
济南中阳石磨电器有限公司

鲁公网安备 37018102000574号